24gp-370 DC 6V 12V 24V High Torque 25KG.CM Planetary Geared Electric Motor

This motor can choose two shaft diameters, 4mm and 6mm.

You can choose one of the shaft diameters, and the shaft type of the two will be slightly different.

The following is the dimension drawing of the motor with a shaft diameter of 4MM

Important reminder

Because we use different measuring tools, so the measurement data of the product size will be slightly different.

If your project has high requirements for the size of the motor, we recommend that you contact us before purchasing.Thank you very much!

We name the length of the gearbox L. Note that the length of the gearbox will vary with the speed of the motor. For details, please refer to the L length of the corresponding parameter in the following parameter table.

The length of the gearbox is about 20.5mm to 32.2mm. The length of the gearbox is different for different speeds, so please check the corresponding gearbox length in the parameter table according to the speed you choose.

The following is the dimension drawing of the motor with a shaft diameter of 6MM

Important reminder

Because we use different measuring tools, so the measurement data of the product size will be slightly different.

If your project has high requirements for the size of the motor, we recommend that you contact us before purchasing.Thank you very much!

We name the length of the gearbox L. Note that the length of the gearbox will vary with the speed of the motor. For details, please refer to the L length of the corresponding parameter in the following parameter table.

The length of the gearbox is about 20.5mm to 32.2mm. The length of the gearbox is different for different speeds, so please check the corresponding gearbox length in the parameter table according to the speed you choose.

Important reminder, the length of the reducer is different, and the overall length of the motor is also different. After selecting the voltage and no-load speed of the motor, you need to check the corresponding length of the gearbox, and then you can refer to the dimension drawing above to get the total length of the motor.

Refer to the diagram below to simply calculate the torque required for your project, which is the rated load torque of the motor you should choose.

The following are Figures A and B, respectively

The radius of Figure A is 1CM, which means that the radius of the object driven by the motor is 1CM, and the weight of the object is 10KG, then the motor torque you need to choose is 10KG.CM;

The radius of Figure B is 10CM, which means that the radius of the object driven by the motor is 10CM, and the weight of the object is 10KG, then the motor torque you need to choose is 100KG.CM;

Simply put, the load of your project needs to be inferred from the radius of the object, not just the weight of the object.

It is calculated as follows

Calculate the required torque = the radius of the driven object CM* times the weight of the object

The following introduces the basic information of this motor

(1) Name of the motor: DC Planetary Encoder Geared Motor

(2) Rated voltage : DC 6V , DC 12V And DC 24V

(3) No load speed have:

40 / 48 / 60 / 94 / 240 / 375 / 1200 RPM / Min

(4) About the rated load torque of the motor: the no-load speed of the motor is different, the torque will also be different, the lower the speed you choose this motor, the greater the torque of the motor;

In short, the slower the motor spins, the heavier the load it can drive, and the faster the motor spins, the lighter the load it can drive.

Some people will have a doubt. If the maximum speed of this motor is purchased, such as 1200rpm, if we reduce the speed of the motor from 1200rpm to 40rpm, when the motor is running at 40rpm, can the torque of the motor reach 15KG ?

This is impossible. When the speed of the motor is adjusted, the torque of the motor will also decrease as the speed decreases. For example, the speed of the motor you bought is 1200rpm, and the torque of the motor is 1.5KGF.CM . When you reduce the speed of the motor, the torque of the motor will be lower than 1.5KG. If the speed of the motor is greatly reduced, the torque of the motor will also be greatly reduced.

If you buy the lowest speed of this motor, such as 40rpm, the torque of the motor is 15KG, if you reduce the speed of the motor from 40rpm to 1rpm, the torque of the motor will also be lower than 15KG.

So you need to consider whether the final torque of the motor can reach the load of your project after the motor is decelerated. If not, you need to consider choosing other lower speeds or other motors.

You can contact us about the principle of torque change with speed, we can help you avoid buying mistakes, thanks!

(5) Direction of rotation of the motor: CW Or CCW ; Support Reversed

(6) Gear material: Metal gears make the motor last longer

(7) The speed of the motor can be adjusted using the speed controller. If you also need a speed controller, you can contact us and we will recommend the most suitable controller for you.

For example, the speed of the motor is 40rpm, you can adjust speed from 0rpm to 40rpm or 40rpm to 0rpm through the speed controller,that is, the speed you choose to buy is the adjustable range Maximum speed.

However, if you use a speed controller to control the rotation speed of the motor, the torque of the motor will decrease as the speed decreases. If the torque of the motor is lower than the load of your project, the motor will be damaged, you need to pay special attention.

(8) This motor is suitable for a variety of micro-automation equipment. As long as you confirm that the motor voltage and torque of your choice are suitable for the voltage and load of your project before purchase, there is no limit to the scope of use of this motor.

For example, Smart Robot ; Smart Door Lock ; DIY tank etc.

The following is a description of the quality materials and structures of this motor.

① Gearbox outer wall

② The output shaft of the motor is available with a shaft diameter of 4mm and 6mm

③ Planetary gear, using thickened metal gear, high strength, reduce noise, make the motor run stably

④ Planetary gear frame

⑤ Connecting plate

⑥ DC brushed high-speed motor

⑦ Hall encoder

⑧ M2.5 screw holes